The LM-2 combines an air/fuel ratio meter, a full-function 32-channel datalogger, and powerful software to deliver a complete tuning workshop for less than the cost of one dyno day.
Whether you have a piggy-back fuel controller, race carb, aftermarket ECU, ODB-II tuning software, or a flash/chip programmer, an LM-2 is the tool you need to dial in maximum HP. The meter’s digital signal processing technology provides data on exactly how rich or lean an engine is running at any load. The LM-2’s self-calibrating circuitry also compensates for changes in temperature, altitude, and sensor condition.
Innovate “Direct Digital” Wideband Measurement Circuit
LM-2 can be conneted to any other Innovate device an log any data aquired by these devices.
Single or Dual Channel Version Available
• OBD-II Scan tool- read and clear trouble codes, and log OBD-II channels
• Log directly to SD card
• Playback log data on screen or with powerful analysis software LogWorks 3.0
• High-contrast graphics LCD
• Built-in RPM converter (inductive clamp or direct frequency)
• 4 fully-differential analog inputs (0-5V DC)
• 2 configurable analog outputs
• Positive lock connectors for all connections
• Innovate MTS serial in and out
• USB connection
LM-2 comes with:
• Bosch Wideband Sensor LSU 4.2
• O² Sensor Cable
• RPM/Analog In/out cable
• OBD-II cable
• USB to PC cable
• 1GB SD card
• 12V cig lighter cable
• CD ROM with LogWorks Software
all packed in a plastic carrying and protection case.
We recommend these accessories:
 |
Window Mount for LM-2High Quality window mount for LM-2 49,00 EUR ( 19 % VAT incl. excl. Shipping costs ) 3-4 Days |
 |
LM-2 Carrying caseCase for secure transport and protection of your LM-2. (Shipping without any Tools) 59,00 EUR ( 19 % VAT incl. excl. Shipping costs ) 3-4 Days |
 |
Sensorcable for LM-2, MTX-L 18ftExtended sensor cable 18ft, to connect the O² Sensor to the LMA-2 69,90 EUR ( 19 % VAT incl. excl. Shipping costs ) 3-4 Days |
 |
Sensorcable for LM-2, 8ftStandard sensor cable 8ft, to connect the O² Sensor to the LMA-2 43,00 EUR ( 19 % VAT incl. excl. Shipping costs ) 3-4 Days |
 |
LM-2 OBD-II CableTo connect the LM-2 to the vehicles OBD-II port. (As Included in the LM-2 Complete Kit) 5 1/2 ft
24,89 EUR ( 19 % VAT incl. excl. Shipping costs ) 3-4 Days |
 |
LM-2 patch cable to MTS devicesTo connect the LM-2 to any Innovate MTS device (e.g. LMA-3, SSI-4, TC-4, DL32 etc.) 13,90 EUR ( 19 % VAT incl. excl. Shipping costs ) 3-4 Days |
 |
LM-2 Analog/RPM In/Out cableAnalog Input and Output Accessory Cable for LM-2 (Needed for RPM Input).and also for output of AFR signal to feed ino ECUs 24,89 EUR ( 19 % VAT incl. excl. Shipping costs ) 3-4 Days |
 |
LM-2 power cable 12 VLM-2 power cable with cig lighter plug 15,90 EUR ( 19 % VAT incl. excl. Shipping costs ) 3-4 Days |
 |
Inductive pickup clampInductive pickup clamp, for RPM pickup at ignition cable.
32,00 EUR ( 19 % VAT incl. excl. Shipping costs ) 3-4 Days |
 |
Bosch LSU4.2 5-wire, wide-band O2 sensorStandard sensor shipping with LM-2 and LC-1
79,00 EUR ( 19 % VAT incl. excl. Shipping costs ) 3-4 Days |
 |
Bung & Plug, mild steelAccepting the O2 sensor, to be welded into the exhaust system. NOT stainless, 1" long. (1 pc. comes with each LM-2 and LC-1)
9,90 EUR ( 19 % VAT incl. excl. Shipping costs ) 3-4 Days |
 |
Exhaust clamp for O2 sensorPatent-pending, Venturi-effect, tapped exhaust clamp for obtaining accurate lambda measurements in non-cat autos or other engines. Pushing the O2 sensor into the tail pipe, without this exhaust clamp, does not deliver correct results 75,00 EUR ( 19 % VAT incl. excl. Shipping costs ) 3-4 Days |
 |
Bung & Plug Extended (1 inch) Stainless SteelBung & Plug Extended (1 inch) Stainless Steel 10,90 EUR ( 19 % VAT incl. excl. Shipping costs ) 3-4 Days |
 |
Bung & Plug, mild steelAccepting the O2 sensor, to be welded into the exhaust system. NOT stainless, 1" long. (1 pc. comes with each LM-2 and LC-1)
8,90 EUR ( 19 % VAT incl. excl. Shipping costs ) 3-4 Days |
|
Bung & Plug, mild steelAccepting the O2 sensor, to be welded into the exhaust system. NOT stainless, 1" long. (1 pc. comes with each LM-2 and LC-1)
9,90 EUR ( 19 % VAT incl. excl. Shipping costs ) 3-4 Days |
 |
12mm to 18mm Motorcycle Bung Adapter34,90 EUR ( 19 % VAT incl. excl. Shipping costs ) 3-4 Days |
Customers who bought this product also bought the following products:
|
Sensorcable for LM-2, MTX-L 18ftExtended sensor cable 18ft, to connect the O² Sensor to the LMA-2 69,90 EUR (19 % VAT incl. excl. Shipping costs) |
|
Bosch LSU4.2 5-wire, wide-band O2 sensorStandard sensor shipping with LM-2 and LC-1
79,00 EUR (19 % VAT incl. excl. Shipping costs) |
|
Bung & Plug, mild steelAccepting the O2 sensor, to be welded into the exhaust system. NOT stainless, 1" long. (1 pc. comes with each LM-2 and LC-1) 9,90 EUR (19 % VAT incl. excl. Shipping costs) |
|
Bung & Plug Extended (1 inch) Stainless SteelBung & Plug Extended (1 inch) Stainless Steel |
 |
LMA-3The LMA-3 (AuxBox) features internal sensors and can accept signals from external sensors (0-5V) too. It either attaches to the auxiliary input of the LM-1 or can be run as a MTS device in a LogChain, connected to other devices. 229,00 EUR (19 % VAT incl. excl. Shipping costs) |
|
Exhaust clamp for O2 sensorPatent-pending, Venturi-effect, tapped exhaust clamp for obtaining accurate lambda measurements in non-cat autos or other engines. Pushing the O2 sensor into the tail pipe, without this exhaust clamp, does not deliver correct results 75,00 EUR (19 % VAT incl. excl. Shipping costs) |
This Product was added to our catalogue on Tuesday 04 January, 2011.